One of the main problems facing our planet is that of plastic garbage, which is difficult to degrade and occupies large volumes that are difficult to process. Much of this garbage is made up of plastics derived from ...

Additive manufacturing in polymers is a process for obtaining parts on the rise, due to its ability to transform raw material into serial or custom parts with many applications in various sectors. When studying to change a...

The increase in demand for electric vehicles, as well as for electrical and electronic equipment (AEE), implies the generation of a large amount of hazardous waste at the end of its useful life, in addition to representing a significant loss of ...

The use of industrial waste as by-products and its recovery in the value chain of producing companies is a great environmental and economic challenge for any company. In this sense, ELECTROFEM aims to recover energy, ...

The incorporation of fibers to mortars allows improving their performance, tensile strength, ductility, energy absorption capacity, fatigue behaviour, and resistance to abrasion and impact. When the fibers are vegetable as is the case...

The objective of this project is the study and evaluation of adult stems (with the possibility of logging for quality wood uses such as structural use), of the most representative pine in the Valencian Community, Pinus halepensis (pine ...

In a project already developed by AIDIMME (INTERBOT), the development of an interface for programming robots through verbal commands was proposed. During the development of the project, the problems presented by carrying out a robot program were revealed ...

In the paint production, phytosanitary and metal-mechanic sectors, dangerous liquid chemical substances and mixtures are used, such as certain acids, bases, solvents and toxins, normally classified as dangerous goods, which must be transported in good quality containers. Many of...

This project proposes to investigate with a scope and objectives where the integration of three enabling technologies of the Industry 4.0 concept is required: additive manufacturing technology, parts inspection systems and artificial intelligence systems. According to ...

SMARTCHAIR will investigate the problems associated with a wheelchair system that moves between two points in the environment using a beacon positioning system in the form of a mesh network (MESH), developed in the IMOLAB project and that detects ...

The purpose of the project is to promote the application of the circular economy in the entities and companies of "Paterna Ciudad de Empresas" through the establishment of synergies of industrial symbiosis. The project includes actions for the dissemination, awareness-raising and promotion of ...

During 2023, it is intended to encourage the participation of companies in the Valencian Community in the creation of industrial ecosystems based on industrial symbiosis and the circular economy, in order to promote a circular economic model, through the use of ...

The project pursues the increase of excellence in advanced additive manufacturing, to improve networking and reduce technological deficiencies, significantly reinforcing the excellence and innovation capacity of research in this field...

The project arises from the need to improve industrial processes through advanced digitization tools and introduce digital functionality in new products and developments. For this, an advanced haptic device will be developed to complement the development ...

The digital twin of a robot arm will be developed so that it can be operated virtually by a user, and the robot responds in real time.

Currently and due to the restrictions in the commercialization of combustion vehicles, the transition to electric vehicles is being carried out. To do this, it must be validated that the elements that store energy meet the demanding automotive requirements to ...

In recent years, the study, control and investigation of biocide efficacy has increased, both for bacteria and for fungi and viruses. In the case of viruses and, to a lesser extent, fungi and bacteria, the results can ...

Corrosion is a typical defect of metal surfaces due to the oxidation process. To reduce this effect and increase the durability of materials, metal parts are coated as a protection method. Even so, the deterioration of the material depends ...

Generation of a system that allows the development and circulation of products with mainly melamine surfaces, safe for citizens. Generate a tool that reliably determines which products can meet the security criteria of the legislation, as well as to ...

The SISPATINT 2023 project, belonging to the AIDIMME Biomaterials R&D line, consists of several applied research activities to test, configure and improve the PATINT system, as well as activities for the study and analysis of biomaterials and ...

The purpose of the project is to evaluate the reliability of the generation of simulation models as a predictive tool to be able to reproduce the behavior of seating furniture subjected to different tests included in current regulations. To do this, you will...

InnDIH is the Valencia Region DIH, representing the major public-private collaboration among the business ecosystem, universities, technological and research centers and public agencies, for the digitalization of SMEs and Public Administration (PA). Promoted by AVI (Valencia Innovation Agency) and coordinated by ITI, ...

The Industrial Symbiosis Observatory is a technology transfer and Competitive Intelligence tool aimed at collecting, filtering and disseminating relevant information on Industrial Symbiosis to facilitate its implementation in companies in the Valencian Community.

During the year 2022, the development of the following demonstrators has been launched: • Additive manufacturing (AM) • Robotics • Virtual reality/Augmented reality (VR/AR). In the 2023 annuity, the development of applications that use these demonstrators on digitization technologies is proposed, from the ...

Study and development of a high protection additive manufacturing process based on multi laser direct wire deposition (LWMD) for the processing of highly reactive materials. Application to implants in Ti64-ELI

During the last decades, plastic metallization processes have gained strength in sectors such as automobiles, white goods, electronics, bathroom accessories, cosmetics, etc. The search for lightweight materials to reduce the weight of automobiles has ...

The general objective of the project is to investigate, develop and characterize an innovative thermal insulation system for buildings based on wood or derived materials, and therefore sustainable and with a low environmental impact. Also, the system...

The Valencian Community has large areas dedicated to agriculture and Mediterranean mountains, where there are vegetable accumulations that can cause serious problems in the conservation of the environment (fires, pests, release of CO2 due to its elimination through combustion, etc.). On the other hand, ...

The project delves into the development and application in situ of highly sustainable prefabricated interior building envelopes from CV-specific biomaterials without industrial use and recycled materials from construction demolition (RCD), from ...

The high level of demand in some fields of industry such as the energy or aerospace sector requires materials in constant evolution. These sectors are always on alert before the appearance of new materials in any of their ...

The non-dependence on fossil fuels is one of the greatest challenges of our society, increasingly technological and globalized, where transport and communications mark its progress. That is why the search for...

The increase in demand for electrical and electronic equipment (EEE) and the decrease in useful life generate a huge amount of waste electrical and electronic equipment (WEEE) from equipment such as mobile phones, television, computers, printers, modems, ...

Currently, the majority of forest masses in the Valencian Community are not being exploited for various reasons. Among them is the lack of knowledge of the resource that is owned, where exactly it is located or the quality that this resource can offer. ...

The FORESPINT project wants to provide a different and closer to the market outlet for the residual forest and agricultural biomass of the Valencian Community, incorporating bioproducts with antimicrobial activity extracted from certain residues in coatings for the...

The project proposes to advance in the development of techniques that allow speeding up the programming of robots by applying Learning by Demonstration techniques based on the results obtained in a previous project (COLEARNING 4.0 - Development of learning techniques for ...

Fiber-reinforced concrete improves the nonlinear behavior of concrete, especially against tensile stresses, stitching cracks, preventing them from spreading and allowing the concrete to continue resisting traction, being especially effective in resisting dynamic loads or ...

The PROTECTOR project focuses on improving the hybrid LMD-CNC manufacturing process to be able to process metals with greater protection against oxidation. For this, it is intended to design and install a protection system for the manufacturing area to...

The objective of the project is to investigate the feeding apparatus of certain Mediterranean marine species, such as the basking shark or the manta diablo, through physical and virtual simulations to understand the hydrodynamic mechanisms that provide the efficiency of microplankton capture. ..

Resources are vital to the economy and are essential to the operation and integrity of industrial systems. However, certain types of raw materials (critical raw materials) present a high supply risk, either because of their high...

Investigate the automation of productive processes in construction, introducing automatic systems so that the space where a work is going to be carried out really becomes a layout of interrelated and automatically communicated processes, analyzing ...

The INPROTEM project is going to investigate the protection capacity of different packaging materials, taking as a reference factor the conditions of temperature and relative humidity that occur in the logistics cycles of any industrial product. The ...

The heterogeneity in fire behavior evaluation systems and the increase in possible applications of materials and products in other sectors motivate the development of the PREFIRETOOL project. The proposed experimental research aims to establish the relationships between several parameters ...

This project proposes to develop an intelligent mobility laboratory (iMoLab) through a coordinated R&D action that makes it possible to have prototypes/demonstrators of a distributed intelligent mobility laboratory.

Create a work methodology that gives rise to the systematized development of digital energy models of buildings that allow the analysis of the energy state and support in the decision-making process associated with the implementation of improvements of ...

Reverse osmosis (RO) and ion exchange (IE) are perceived as viable and feasible solutions to address freshwater scarcity, through seawater desalination and wastewater reuse, and to provide water...

The main objective of the project is the development of a platform (LogiBlock), which facilitates the deployment, planning, management and supervision of fleets of robots and autonomous vehicles in small and medium-sized companies, to carry out logistics tasks in industrial environments.

In this project, it is intended to obtain viricidal substances for SARS-CoV-2 based on prior knowledge of antimicrobial and bactericidal materials. Thanks to this, the material itself will degrade the virus, preventing it from being infective and cutting the chain of ...

The EU furniture industry is a labor-intensive sector dominated by SMEs, which is facing nowadays different challenges such as increasing competition from countries with lower production costs, increasing raw materials and labor costs, an aging workforce and difficulties in attracting younger ...

Improving industrial energy efficiency at European Manufacturing level requires the integration of energy data with advanced optimization techniques to guide a company decision making. E2COMATION intends to address the optimization of energy usage, at multiple hierarchical layers of a manufacturing process as well as ...

Democratized innovation holds undeniable promise for European producers, but the integration with corporate innovation practices is in its infancy. While the interest is real, it is still neither easy or efficient for producers - especially SMEs to benefit from collaborative production. ...

The eFactory project realizes a federated smart factory ecosystem by primarily interlinking 4 smart factory platforms, from the FoF-11-2016 cluster, through an open and interoperable Data Spine. The federation of the 4 base platforms is complemented by industrial platforms, collaboration tools ...